Supported Devices
eSSL K90 Pro
- Fingerprint + RFID Card
- LAN (Ethernet) connection
- Best for: Main gate, high-traffic areas
Fingerprint capacity and transaction log capacity vary by variant. Confirm the exact figures with your device supplier.
eSSL F22 (Wi-Fi)
- Fingerprint only
- Wi-Fi + LAN connection
- Best for: Classrooms, staff rooms, flexible placement
Fingerprint capacity and transaction log capacity vary by variant. Confirm the exact figures with your device supplier.
What You Need Before Starting
- Your biometric device (K90 Pro or F22), powered on
- Internet access at your school — the device needs to reach the LigiLearn server over the internet. Your phone or laptop does not need to be on the same network as the device.
- The device’s Serial Number (printed on the back label, or visible in the device’s System Info menu — the exact menu path may differ by model variant or firmware)
- Admin access to LigiLearn
- Students and staff already added in LigiLearn
Step 1: Register the Device in LigiLearn
Tell LigiLearn about your device so it knows which machine is sending attendance data.
- Log in to LigiLearn as Admin
- Go to Operations → Biometric → Devices
- Click + Add Device
-
Fill in the fields below.
- Device Code
- A short label for your reference, like
GATE-01orSTAFF-ROOM - Serial Number
- The serial number from your device — must match exactly
- Device Name
- A friendly name, like
Main Gate Scanner - Location
- Where it is installed, like
Front Gate - Allowed Users
- Choose
Students & Staff, or just one type if needed
- Click Save
Step 2: Enrol Fingerprints on the Device
Before LigiLearn can record anyone’s attendance, each person must have their
fingerprint registered on the device itself. During enrolment the
device assigns a User ID (also called a PIN), such as 001 or 042.
- On the device, open the user enrolment menu (the exact menu path varies by model and firmware — look for User Management or Enrol User)
- Enter or accept a User ID / PIN for the person
(e.g.
001) - Ask the person to place their finger on the scanner to register their fingerprint
- Write down the PIN — you will need it in the next step
Step 3: Map PINs to Students/Staff in LigiLearn
Tell LigiLearn which device PIN belongs to which person. Without this mapping, punches will appear as “Unmapped” in the Punch Log.
- Go to Operations → Biometric → User Mapping
- Click + Add Mapping
- Enter the Device PIN exactly as it appears on the device
(including any leading zeros —
001is different from1) - Choose User Type: Student or Employee
- Search and select the correct person
- Click Save
- Repeat for each enrolled person
Step 4A: eSSL K90 Pro — Network & Server Setup
Connect to your network
- Connect a LAN (Ethernet) cable from your router or switch to the K90 Pro
- On the device, open the network or Ethernet settings (often under Comm. or Communication)
- Enable DHCP so the device gets an IP address automatically, or set a static IP if your network requires it
- Save the settings
Configure ADMS / Cloud Server
- On the device, open the ADMS or Cloud Server setting (often under Comm. → Cloud Server Setting — the exact menu name may differ by firmware)
- Set the Server Address to:
ligilearn-api.ligimex.in - Set the Port and HTTPS / TLS setting to match
your LigiLearn server. If the device supports HTTPS, use port
443. If it only supports plain HTTP, contact LigiLearn support for the correct port. - Enable ADMS / Cloud Server
- Save the settings
http://, https://, or any path like /iclock.
The device adds the required path automatically.
Step 4B: eSSL F22 (Wi-Fi) — Network & Server Setup
The F22 supports both Wi-Fi and LAN. Choose whichever is more reliable at your location.
Option A: Connect via Wi-Fi
- On the device, open the Wi-Fi settings (look under Comm. or Communication)
- Enable Wi-Fi and select your school’s network
- Enter the Wi-Fi password and wait for the connection icon to appear
Option B: Connect via LAN
Same as K90 Pro — plug in a cable and enable DHCP or set a static IP.
Configure ADMS / Cloud Server
Follow the same ADMS steps as the K90 Pro above — set the server address to
ligilearn-api.ligimex.in, choose the correct port
and HTTPS setting, enable the cloud server, and save.
Step 5: End-to-End Installation Test
Do not leave the site until every item below is confirmed.
- Heartbeat: In LigiLearn, go to Biometric → Devices. The Last Heartbeat column should show a recent time (within the last minute). If it still says Never, the device is not reaching the server — recheck the network and ADMS settings.
- Test punch: Ask the test person you enrolled in Step 2 to place their finger on the device. The device should confirm the scan.
- Punch Log: Go to Operations → Biometric → Punch Log. The punch should appear within a few seconds with the correct person’s name, the right time, and a Processed status.
- Attendance record: Go to the relevant attendance screen and confirm that the punch resulted in a Check-In or Check-Out record for the correct person.
- Check-In vs Check-Out: The device sends a status code that tells LigiLearn whether the punch is a Check-In or Check-Out. How the device decides this depends on its own settings — some devices alternate automatically, others require the user to select. Confirm on your device how it works and verify that LigiLearn records the direction correctly.
Offline Behaviour
If the internet goes down, the device continues to record punches in its internal memory. When the connection is restored, the device typically uploads the stored punches to LigiLearn automatically.
- The number of punches the device can store locally depends on the model variant — confirm with your device supplier.
- When the internet returns, the device re-sends buffered punches. If LigiLearn has already recorded a punch with the same person and timestamp, the duplicate is discarded.
- If the device runs out of local storage before the internet returns, older records may be overwritten. Check your device’s buffer policy.
Optional: Offline test
- Disconnect the device from the network (unplug the LAN cable or turn off Wi-Fi)
- Record a test punch on the device
- Reconnect the network
- Check Punch Log in LigiLearn — the test punch should appear after the device reconnects and uploads its buffer
Troubleshooting
Heartbeat still shows “Never”
- Check that the LAN cable is firmly connected (or Wi-Fi is connected on F22)
- On the device, verify the IP address is not
0.0.0.0 - Confirm the server address is exactly
ligilearn-api.ligimex.inwith no extra characters, spaces, or paths - Confirm ADMS / Cloud Server is enabled on the device
- Confirm the serial number in LigiLearn matches the device exactly
- Check whether the school’s firewall or router blocks outgoing connections on the configured port
Punch is missing from the Punch Log
- Wait 30 seconds and refresh — there may be a short delay
- Check that the heartbeat is recent; if not, the device is offline
- Verify the device is registered in LigiLearn with the correct serial number
Person shows as “Unmapped”
- Go to User Mapping and check that the PIN matches exactly (including leading zeros)
- Add or correct the mapping; future punches for that PIN will then be processed
Punch time is wrong
- The time comes from the device’s own clock. Check the date and time settings on the device and correct them if needed.
Common Questions
Can I use multiple devices at one school?
Yes. Register each device separately with its own serial number. All devices at the same school share the same PIN mappings — a student can punch on any registered device.
Can I still mark attendance manually?
Yes. The regular attendance screen works as before. A biometric punch will not overwrite a manually recorded attendance entry for the same session.
Does LigiLearn store fingerprints?
No. Fingerprint data stays on the device only. LigiLearn receives only the PIN number, the time, and the scan method (fingerprint, card, etc.) — never the fingerprint template or image.
What if a student punches on the wrong device?
As long as that device is registered to your school and the PIN is mapped, the punch will be recorded correctly.
Need Help?
Contact our support team with the following information:
- Your school name
- Device model and variant (e.g. K90 Pro, F22 Wi-Fi)
- Firmware version, if visible on the device
- Device serial number
- Approximate time of the punch you are troubleshooting
- Screenshots of the device’s network and ADMS settings